One Solution™ Dispenser - 简单的按钮

按钮化学分配器

项目# 112944

One Solution™ Dispenser - 简单的按钮

按钮化学分配器

项目# 112944

选项:

需要帮助? 打电话给澳门威尼斯人赌城网站 1-800-321-8180

最喜欢的分享

Accurate dilution can be set to 1 OZ, 3/4 OZ or 1/2 OZ 每个中风
Low profile and rugged design stands up to heavy use and assures long life
Great for bottle, bucket or sink filling when no water source is available

产品描述

Designed to work with the One Solution™ cleaning system, the 简单的按钮 provides an easy way to achieve accurate product dilutions in cramped quarters, small applications or where a water source is not available.

优势
No contact with concentrated chemicals provides added safety to workers
Accurate dilution: Can be set to 1 oz., 3/4 oz.，或1/2盎司. 每个中风
Low profile and rugged design stands up to hard use and assures long life
Versatile: Great for bottle, bucket, or sink filling.

Can also be used to dispense concentrate into larger equipment such as carpet extractors and auto scrubbers. As the name states, operation is simple. Fill a bottle or bucket with the appropriate amount of water and then use the 简单的按钮 to dispense the accurate dose of product and mix together to create a Ready-To-Use solution that is both cost effective and accurate every time. No more guessing and mixing concentrates at incorrect solutions. The One Solution™ 简单的按钮 yields cost-effective, accurate dilutions every time.

使用说明

1. Find suitable place close to water source for unit. Mounting bracket should be installed approx. 离地面5英尺. 调平支架并标记孔. Drill 9/32” holes and install mounting anchors and screws in bracket. 2. Remove cabinet cover and hang cabinet on bracket. Mark hole for lower cabinet screw. Remove cabinet and drill 9/32” hole. Install anchor and screw in lower cabinet hole. When mounting unit, do not mount more than 5 feet from the floor. Also, never mount your concentrate container higher than the unit. Keyhole slots are also provided in the cabinet back if the mounting bracket won’t be used. 3. Select a metering tip (see next section), and insert into hose barb on eductor body. (对所有的教育工作者重复上述步骤.) 4. Supply tube should reach from hose barb on eductor to bottom of the concentrate container. Cut supply tube provided to length required. Slide a ceramic weight over one end of tube and slide a foot valve into the same end of the tube. (Prepare a tube for each eductor.) 5. Push other end of supply tube over the hose barb/metering tip on the eductor. (对所有的教育工作者重复上述步骤.) 6. Place foot valve ends of supply tubes into concentrate containers. REMEMBER TO CHECK FOOT VALVE STRAINERS REGULARLY FOR CLOGGING: CLEAN IF NECESSARY. 7. A short discharge tube is used with the 1GPM eductor; minimum tube length is 8 inches (20cm) for proper operation.
Longer tubes (4 feet) are used with a 3.5 . GPM教育. Slide end of tube over eductor discharge outlet. (对所有的教育工作者重复上述步骤.) Hooks may be installed on longer tubes to allow discharge tube to conveniently hang from dispenser when not in use. 8. 更换机柜盖. Guide supply tubes through slots in sides of cabinet cover. Push the sides in, behind the latch holes, to snap the
盖好. The two screws provided may be installed in the holes in the cabinet sides to prevent easy removal of cover. 9. Connect water supply hose of at least 3/8” ID to water inlet swivel. (Minimum 25 PSI pressure, with water running, is required for proper operation.) Connect opposite end of hose to water supply. 打开供水系统. 10. Purge air from the system by depressing the buttons briefly. There may be some water discharge from the eductor 通风口 until the air is purged. 11. Push button to start flow of desired water/concentrate solution, and hold until supply tube is primed (filled). Then push the button whenever dispensing is desired, and release button to stop flow of solution. If you wish to be able to lock the button in the “on” position: Depress button and slide
按钮锁定. To unlock, depress button and release. 12. It is essential that the discharge hose not be obstructed. If discharge is restricted, water will flow out the eductor
通风口. Do not start to operate the dispenser with liquid in the discharge tube.